Originally Posted by machgsxr (Post 1443770)

ATTT: DANIEL

2r3z6312baa - Crank pulley /Harmonic Balancer
f1az6378a - washer for balancer
f5rz6a340b - bolt for balancer
2r3z6312ba - Supercharger Crank drive pulley
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z6b209bc - Pulley bridge assembly for S.C. (If bought new it comes with the bridge, 2 idlers and tensioner)
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
(6D080) Timing cover (if bought new, it comes w/ pulley on drivers side and tensioner)
s5az6700a - timing cover seal
(10A313) Upper alternator bracket
(10153) Lower alternator bracket
(10346) Alternator
1U2Z-14S411-TA Electrical connector (alt. to harmness )
(6B209A) Tensioner on timing cover
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
2r3z8548aa - Water cross over pipe
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9424bb - Lower intake
(6K775) Garrett factory intercooler
3U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
f8yz8501aa - Ford / Bosche water pump for intercooler
2r3z8n500ac - Intercooler pump
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9N491B) Lower manifold to intercooler water adapter
2r3z9a589ca - Plenum
(9B659) Intake tube from maf to t/b.
(9F715) IAC valve
2r3z9a825aa - Cruise control cable
2r3z9a758aa - Throttle cable
(9728) Throttle and cruise control cable mounting bracket
1l3z12b579aa - MAF
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
(9E498) Hose's or tube cluster of connectors for the vacuum parts above
e83z9f670a IAC gasket
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
e6az9d476b - EGR gasket
2r3z3490aa - Power steering resevoir bracket.
I/C resivoir tank
i/c pigtail
S/C 8 rib belt
inner acc. belt.
n804178s309 - (8) Nuts for plenum, coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt
n811313s431 (4) studs to bolt plenum to s/c
w506404s437 (10) i/c to s/c bolts

Originally Posted by WNTAMACH1 (Post 1443869)

thank u sir! search is on!

Originally Posted by WNTAMACH1 (Post 1443872)

Ya Ya, Build the engine and throw a 3.4 Whipple on top ;)

Originally Posted by machgsxr (Post 1443770)

ATTT: DANIEL


2r3z6312baa - Crank pulley /Harmonic Balancer
f1az6378a - washer for balancer - $3.68
f5rz6a340b - bolt for balancer - $6.04
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used) - $58.86
yw7z8678aa - pulley for above bracket
2r3z6b209bc - Pulley bridge assembly for S.C. (If bought new it comes with the bridge, 2 idlers and tensioner) - $285.80
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
(6D080) Timing cover (if bought new, it comes w/ pulley on drivers side and tensioner)
s5az6700a - timing cover seal
(10A313) Upper alternator bracket
(10153) Lower alternator bracket
(10346) Alternator
1U2Z-14S411-TA Electrical connector (alt. to harmness )
(6B209A) Tensioner on timing cover
2r3z8260ab - Radiator hose - $18.98
2r3z8a593ab - Radiator hose - $24.10
2r3z8k576aa - Radiator hose - $15.18
2r3z8548aa - Water cross over pipe - $75.72
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9424bb - Lower intake
(6K775) Garrett factory intercooler
3U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89
2r3z9l443da - Intercooler line that goes from hard line to hard line - $16.84
f8yz8501aa - Ford / Bosche water pump for intercooler - $175.99
2r3z8n500ac - Intercooler pump bracket - $59.76
2r3z8a193aa - Heat exchanger mounting bracket - $204.75
2r3z8c386aa - 2each bracket clamps for h/e - $20.91
(9N491B) Lower manifold to intercooler water adapter
(9B659) Intake tube from maf to t/b.
(9F715) IAC valve
2r3z9a825aa - Cruise control cable - $20.71
2r3z9a758aa - Throttle cable - $31.98
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
2r3z6020aa - Timing cover gasket LH side - $8.37
2r3z6020ba -Timing cover gasket middle - $10.99
2r3z6020ca - Timing cover gasket RH side - $8.10
2r3z9h486aa - Lower intake to S.C. gasket - $14.29
2r3z9l437bb - Plenum to S/C gasket - $9.72
2r3z3490aa - Power steering resevoir bracket. - $196.86
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover. - $3.85
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these. - $3.30
n808920s437 - Pulley bridge bolts - $2.20
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket - $0.55
N605909s437 - (4) bolts for the upper alt. bracket - $1.10
n807274s437 (1) lower alt. bracket to alt bolt- $0.55

Originally Posted by machgsxr (Post 1444892)

Got as much pricing as I could. Ill text you tomorrow.

Originally Posted by ASMACH (Post 1444956)

Anyone running 4.10's with a built motor and a 2.76 pulley? Im wondering if ill just be spinning all day on the street.

Originally Posted by machgsxr (Post 1443770)

ATTT: DANIEL

f1az6378a - washer for balancer
f5rz6a340b - bolt for balancer
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
2r3z8548aa - Water cross over pipe
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
f8yz8501aa - Ford / Bosche water pump for intercooler
2r3z8n500ac - Intercooler pump
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9B659) Intake tube from maf to t/b
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
i/c pigtail
Inner acc 6 rib belt
n80478s309 - (4) coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt

Originally Posted by mustangfrank (Post 1451973)

http://www.americanmuscle.com/frpp-a...ory-drive.html

Is that all the piece you need for an eaton swap? injector and supercharger are missing.

Originally Posted by machgsxr (Post 1456500)

These are the parts you need to finish it up. Like i told you, we could try and make those hard lines out of just heater hose if you want to. Save you some money.


gasket for i/c adapter to lower intake - One I sent a picture of.

f5rz6a340b - bolt for balancer - $6.04

2r3z8260ab - Radiator hose - $18.98

2r3z8a593ab - Radiator hose - $24.10

2r3z8k576aa - Radiator hose - $15.18

2r3z6020aa - Timing cover gasket LH side - $8.37

2r3z6020ba -Timing cover gasket middle - $10.99

2r3z6020ca - Timing cover gasket RH side - $8.10

2r3z9h486aa - Lower intake to S.C. gasket - $14.29

i/c pigtail

Inner acc 6 rib belt

I would just get all the parts above new from Ford unless they have them cheaper at the local parts store.
------------------------------------
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new) - $11.89

s5az6700a - timing cover seal

(10A313) Upper alternator bracket
------------------------------------
Parts below are what you need to drop off next time you swing by.

EGR Delete kit
h/e, mounting brackets and clamps
p/s resevoir bracket
oil cooler and adapter setup
bracket and idler

Originally Posted by machgsxr (Post 1456500)

-gasket for i/c adapter to lower intake - One I sent a picture of.

-2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c) - $92.62 says it is discontinued might call and verify or see if they changed part #'s.

-2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block - $10.88

-(10A313) Upper alternator bracket
------------------------------------

This is whats left to get for my swap!

Originally Posted by SHAKN' 04 (Post 1456822)

Like I said to you in that text, I can make those lines out of just heater hose. Be allot cheaper. What about that guy you swapped some parts with. Check with him to see if he has them. He does not need them at all.

Originally Posted by Cobra Drifter (Post 1461403)

Where did you guys get the pricing for the parts from? Sorry I couldnt read all 23 pages lol.

I just ordered two of the intercooler hoese and one was right on but the other you have is like 1/2 of what I paid :(

3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res. - $19.62
2r3z9l443ba - $10 but mine was $21 (trying to see if they will cut me more of a discount)

Sup Archie, know you from SVTP and bought parts from you over there. My swap in almost done. Next week I should have all my missing hoses and vaccuum caps so it will be ready to start up for the first time in 13 months :)