Re: Official Procharger HP/TQ/mods thread:
Quote:
Nothing is cheap . Does not look like it will get any better either . Our state tax just went to 6% and corp. tax went to 8.25% . We also have a 6% piggy back tax at end of year . Md. is now the worst taxed state in the country . |
Re: Official Procharger HP/TQ/mods thread:
What MAFia works..the one with 12" wire or 36"
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
-Corey |
Re: Official Procharger HP/TQ/mods thread:
Quote:
I believe either, but I am running the 12". |
Re: Official Procharger HP/TQ/mods thread:
Now that I have ordered everything I am looking for someone to install it. I have went to some people that were referred to me. What am I looking at for price to install the sc, pump, inj and tune? Also, people are telling my dad (he is running around asking people since im in iraq) that I need new spark plugs, and I will be running a lot hotter so I should replace my radiator. What are your thoughts?
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
|
Re: Official Procharger HP/TQ/mods thread:
A 4.15 pulley with a D1 is more than a 4.00 pulley right? Or do I have them mixed up. On boost I mean
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
4.15 will slow the compressor down vs the 4.0 thus less boost with the 4.15. |
Re: Official Procharger HP/TQ/mods thread:
I think I need to switch than, Im running a 4.00 pulley which I was told was 10-11psi, so switching to 4.15 would put me around 9-10psi, but this is through manifolds and o/r x, I dont know the boost level on the 4.00 pulley til Feb 9 when it goes dyno n tuned..
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
|
Re: Official Procharger HP/TQ/mods thread:
I quess I may switch to a 4.15 pulley with my D1 on stock bottom end to last a while.
|
Re: Official Procharger HP/TQ/mods thread:
I know I already asked but I just want to make sure Im not blind and cant read. Cobra tanks, needed or not needed to run a P1SC? So far, I have had two businesses tell me I need a cobra tank. Are they just trying to get more money from me? Thanks
|
Re: Official Procharger HP/TQ/mods thread:
No matter what anyone says...you don't need the cobra tank or pumps for that matter. I used my stock tank with an Aviator pump and after 43,000 mi., 18-20 trips down the 1/4 mi., five 20 min.high rpm sessions on the Barber Motorsports Road Course Track and countless local street encounters I have never had a problem with fuel delivery.
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
Your stock fuel tank with an aviator or SVT Focus pump will be fine until you start reaching the high 400 hp range. Then you can switch to dual pumps. |
Re: Official Procharger HP/TQ/mods thread:
The advantage to the Cobra tanks is they're sumped. You can get by with your regular tank, just don't let the fuel level get too low.
|
Re: Official Procharger HP/TQ/mods thread:
Like I said in my previous post.....No matter what others say you don't need the cobra tank or pumps. I have run mine with the low fuel light on without any problems.
|
Re: Official Procharger HP/TQ/mods thread:
Stock bottom end-Yes
Head unit-D1sc Pulley size-4.00 with 10 pounds of boost@6300rpm Fuel system-60lb injectors,Focus fuel pump with BAP Tuner-Xcal 2 by Jon Lund Mods-Bassani Cat-back w/ O/R x-pipe,Php intake spacer Made 468hp & 440tq on Mustang Dyno |
Re: Official Procharger HP/TQ/mods thread:
Nice #'s! Jon Lund knows what he's doing. He tuned my car a little over a year ago. I want to go to a D1 but I'm gona forge it first. Good luck with it!
|
Re: Official Procharger HP/TQ/mods thread:
Quote:
|
Re: Official Procharger HP/TQ/mods thread:
Just got a retune done this weekend.....I'm happy. :wings:
Head unit - P1sc Stock Bottom End - Yes, bone stock longblock Pulley size - 4.00 Seeing 10 lbs of boost @ 6500rpm Fuel system - 42 lb injectors, SVT Focus pump with Kenne Bell BAP Tuner - SCT tune by Tim Barth @ Modular Powerhouse Mods - BBK longtubes, off rd. x-pipe, Magnaflow magnapacks, Anderson Powerpipe, Php intake spacer, ported lower intake. Made 481 rwhp & 440 rwtq on a Dynojet |
Re: Official Procharger HP/TQ/mods thread:
Yeah running a stock maf with mafia
|
Re: Official Procharger HP/TQ/mods thread:
Got my belt slipped fixed and decided to have it retuned.
Head unit - D1sc Stock Bottom End - No, forged rods and pistons 8.5 CR Pulley size - 3.5 Seeing 17-18 lbs of boost @ 6500rpm Fuel system - tiwn GT pumps with 60 lb injectors Tuner - Pro-Dyno Mods - Full exhaust and countless other things. Made 660 rwhp & 565 rwtq on a Dynojet We could not take it to redline because without a modified FPDM and without upgraded lines the car is running out of fuel pressure past 6200 rpms. My tuner says that when these two things are fixed the final numbers should be around 700 rwhp!!!!! Videos and stuff are coming soon. |
Re: Official Procharger HP/TQ/mods thread:
I'm really enjoying reading all the these threads on Mach 1 power! I'm done quite a bit of work on my 2003 Zinc Yellow Mach - for the record:
Head unit - P1SC Stock Engine (except for injectors and tune) Pulley size - 3.7" (11 lbs of boost @ 6500rpm) Fuel system - Cobra Twin Pumps with 42 lb injectors Tuner - Dyno Tuned Performance- VA Beach, VA Mods - SCT Tune via Pro Racer III, Diablo Sport MAFia (set to 4) with stock MAF in blow-thru configuration after intercooler, Bassani Ceramic Coated Headers with CATS/X-Pipe and Mufflers, Centerforce Clutch & Aluminum Flywheel, FRPP Aluminum driveshaft, cold air intake with fenderwell mods w/K&N air filter mounted on opposite side away from engine 489 rwhp @ 6100 rpm & 466 rwtq @ 5000 rpm on a Dynojet I am considering going to Kenne Bell BAP as even the Cobra pumps were maxed out at 100% @ 6100 rpm, although AFR was still good at 11.8:1 at 6500 rpm. I've only got 275's on my rear and they break loose way too easily, so looking at going to 17 x 10.5's and 315's. Does anyone have a good solution to the oil that is drawn back into the head unit and intake system from PCV system? I've got JLT PCV Pre-Filters in both valve covers and I still get some oil in my inake system. What a pain! |
Re: Official Procharger HP/TQ/mods thread:
i have been reading for dys about power adders and the stock bottom end and im curious about how much forged rods and pistons would cost parts+labor, and since the block is already apart, should the crank be upgraded too?
|
All times are GMT -4. The time now is 04:03 AM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com