Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
Spinning is NOT winning... |
Re: TKat13's Mach1 Build Log
so if i wanted to get one of those fans, how and where? what model? etc i need to get a fan thats more slim than our stock without making me overheat cause of lower cfms.
|
Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
Hardest part was setting the ride height; I need 26.5" from ground to fender lip to clear my driveway, leaves about .5" between the concrete and the chin spoiler. Does open up a set of Maximum Motorsports struts and coil-overs with 350lb springs for sale, very limited use. (not a daily driver) |
Re: TKat13's Mach1 Build Log
Here's my latest plans:
Plans this year: 1. New head gasket... 2. Weld on AN-20 fittings to the radiator and connections to all coolant lines on the motor. (prevent another head gasket lift, hose broke and turbo sucked in the coolant) Real braided lines for coolant. 3. Redo the downpipe 4. Minitub - In Progress now 5. Rear coilovers 6. Add adjustable rear lower control arm mounts to rear end. - Done 7. New front coil-overs with 150# springs (strange dual adjustable) 8. Holley HP EFI ECU 9. Upgraded injectors from 80# to either 120 or 160s, pending on what the tuner tells me I need. 10. roll cage 11. Mount battery in the trunk 12. In the process of all this, clean up my engine bay. 13. Box torque boxes. Goals, get the stupid thing to hook, rev past 7k and make 1000rwhp. |
I'm getting more and more curious about the aftermarket ECU's. I'm thinking when the time comes to go for stupid power again I'm going to ditch the stock ECU.
|
Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
Besides, can you really put a price on the Smiles per Mile! |
Re: TKat13's Mach1 Build Log
[QUOTE=DSG2003Mach1;1631441]people are starting to get my attention with this holley stuff. The low impedance fuel injectors are waaaaaaaaaaaaaaaaaaay cheaper too. Like they said, that alone damned near pays for some of these things. /QUOTE]
You hit the nail on the head, the price of injectors is crazy for the IDs, get this kit and it opens the door to the lower cost injectors. I also need a 2-step and bump in... got that too... And if you get crazy, you can have a wide band on each motor side. I already have an E-Boost2 but if you needed a boost controller... its there. This really does save money in the long run. |
Re: TKat13's Mach1 Build Log
Installed the Strange Coil-Overs last night; 150lb springs. As a note to help those cranking the spring up; after struggling with the tension on the driver's side, the passenger side I put some Prothane suspension lube on the surface of the lower spring perch, this allowed me to crank up the spring with ease. Moved like butter.
(need to do some washing in there) https://lh3.googleusercontent.com/g3...w1034-h1378-no The adjustment for these are at the top of the strut and the bottom, did not take a pic of the bottom yet. Compression and Rebound. The hex head is the top adjuster: https://lh3.googleusercontent.com/yN...w1034-h1378-no |
Re: TKat13's Mach1 Build Log
Thank you for this thread! I love it!!
|
Re: TKat13's Mach1 Build Log
Awesome build going on, Darrell..!!!
|
Re: TKat13's Mach1 Build Log
Quote:
Quote:
Something I have always tried to instill into my daughter (19 now); work hard and help more; the less you expect in return, the more you will receive. Honesty above all things. I am very fortunate to have the 'few' friends I have; they are lifers for sure. Love this forum, great place. |
Re: TKat13's Mach1 Build Log
Quote:
I do understand Darrell.. I spend years gutting my Mach 1 to be a pro street/drag car. When I think of the money I dumped into it, I just want to disappear! LOL, carry on soldier!! |
Re: TKat13's Mach1 Build Log
Round 3 has started...
Oil pressure dropped below 5psi when idling so figured it was past time to pull this thing apart and put on the much needed head gaskets and do a through inspection. When the blue tape comes out, you know I mean business. :smokin: https://lh3.googleusercontent.com/b8...w1471-h1103-no About 30 minutes later we have this: https://lh3.googleusercontent.com/qa...=w828-h1103-no Break for a shot of courage and this happened. https://lh3.googleusercontent.com/iV...=w828-h1103-no Turbo kit tossed in the floor. https://lh3.googleusercontent.com/4S...=w828-h1103-no |
Re: TKat13's Mach1 Build Log
While looking around I found this picture from 2004, about 3 months after buying the Mach with my Dog Rusty and a Cat in the car. Yep, towed this thing from Texas to Maryland.
https://lh3.googleusercontent.com/lE...=w1024-h768-no |
Re: TKat13's Mach1 Build Log
As always awesome job..head gasket job a ***** ?? See that in my future, looking at Cometic MLS with ARP hardware set.
|
Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
That is the post he is referring to, I will see if I can find the picture of the label. It is thinner than stock, fits the radiator very well with minor mods, instead of a 'fan' on the radiator it has a shroud as well. |
Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Quote:
|
Re: TKat13's Mach1 Build Log
Ok cool, yea like to see that fan, I took a stocker and used foam door foam around it to get a seal.
|
Re: TKat13's Mach1 Build Log
Quote:
|
All times are GMT -4. The time now is 12:50 PM. |
Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
(c) 2002-2013 Mach1Registry.com